Mechanické vlastnosti a struktura slitiny hliníku po tepelném zpracování

Loading...
Thumbnail Image
Date
ORCID
Mark
B
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Bakalářská práce se zabývá vlivem tepelného zpracování, především pak délky umělého stárnutí, na mechanické vlastnosti slitiny hliníku AlSi7Mg0,6. Jako experimentální materiál byly použity válcové zkušební tyče o průměrech 6 mm a 9 mm, které byl odlity do keramické formy připravené metodou vytavitelného modelu. Zkušební tyče byly odlity firmou Alucast, s.r.o., přičemž při odlévání byla použita touto firmou patentovaná metoda JF casting. U zkušebních tyčí bylo provedeno tepelné zpracování T6 dle normy AMS 2771C, přičemž po rozpouštěcím žíhání následovalo umělé stárnutí v délce od 2 do 12 hodin. K vyhodnocení vlivu délky umělého stárnutí na mechanické vlastnosti zkušebních tyčí obou průměrů byly použity metody světelné mikroskopie, měření tvrdosti dle Brinella, měření parametru DAS pomocí obrazové analýzy a také byla provedena statická zkouška tahem. Na základě provedených experimentů je možné konstatovat, že nejoptimálnějších hodnot mechanických vlastností bylo u zkušebních tyčí, jak o průměru 6 mm tak o průměru 9 mm, dosaženo po 10 hodinách umělého stárnutí.
The presented bachelor´s thesis deals with the influence of heat treatment especially artificial aging on mechanical and structural properties of AlSi7Mg0.6 alloy. Cylindrical test bars of diameter 6 mm and 9 mm cast into a self-supporting ceramic shell made by plaster investment technology were used as experimental samples. These test bars were cast by Alucast whereas the patented technology of casting- JF casting was used. On the test bars was carried out the T6 heat treatment according to the Standards AMS 2771C. After the solution annealing were test bars divided to the six groups and put through various time of artificial aging, namely from 2 to the 12 hours. In order to evaluate the effect of the time of artificial aging on the structure and mechanical properties of both diameters of the test bars, the method of light microscopy, Brinell hardness test and static traction test were used. Also SDAS quantification was carried out by means of image analysis. On the grounds results of experiments it is possible to state, that the best values of mechanical properties of both diameters of the cylindrical test bars were reached after 10 hours of artificial aging.
Description
Citation
ROLEČEK, J. Mechanické vlastnosti a struktura slitiny hliníku po tepelném zpracování [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2012.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Materiálové inženýrství
Comittee
doc. Ing. Bohumil Pacal, CSc. (předseda) doc. Ing. Libor Pantělejev, Ph.D. (místopředseda) prof. Ing. Stanislav Věchet, CSc. (člen) prof. Ing. Martin Trunec, Dr. (člen) doc. RNDr. Karel Obrtlík, CSc. (člen)
Date of acceptance
2012-06-13
Defence
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení
DOI
Collections
Citace PRO