Využití techniky orientovaných fólií v TEM
but.committee | prof. Ing. Jiří Švejcar, CSc. (předseda) prof. Ing. Tomáš Podrábský, CSc. (místopředseda) prof. Ing. Rudolf Foret, CSc. (člen) doc. Ing. Eva Münsterová, CSc. (člen) prof. Ing. Ivo Dlouhý, CSc. (člen) prof. RNDr. Karel Maca, Dr. (člen) prof. Ing. Karel Hrbáček, DrSc. (člen) | cs |
but.defence | cs | |
but.jazyk | čeština (Czech) | |
but.program | Aplikované vědy v inženýrství | cs |
but.result | práce byla úspěšně obhájena | cs |
dc.contributor.advisor | Petrenec, Martin | cs |
dc.contributor.author | Buček, Petr | cs |
dc.contributor.referee | Kruml, Tomáš | cs |
dc.date.accessioned | 2018-10-21T20:28:32Z | |
dc.date.available | 2018-10-21T20:28:32Z | |
dc.date.created | 2009 | cs |
dc.description.abstract | Tato diplomová práce se zabývala využitím metody orientovaných fólií v transmisní elektronové mikroskopii. S použitím této metody byly identifikovány dislokační struktury v obou fázích, pro dvě amplitudy plastické deformace ap, cyklicky zatěžované polykrystalické austeniticko-feritické korozivzdorné oceli SAF 2507. Byly také určeny osy zatěžování jednotlivých zrn a hodnoty Schmidových faktorů aktivních skluzových systémů. V austenitické fázi byla určena planární struktura pro obě ap. Ve feritických zrnech se dislokační uspořádání lišila pro dvě pozorované amplitudy ap. U nižší ap=1x10-4 se nacházely volné šroubové dislokace a nakupení hranových dislokací zatímco u vyšší ap=2x10-3 bylo dislokační struktura tvořena směsí žil a stěn. Pozorované dislokační struktury byly diskutovány s cyklickou plastickou odezvou duplexní oceli. | cs |
dc.description.abstract | The master’s thesis is focused on the application of the technique of oriented foils in transmission electron microscopy. Dislocation structures were identified by this technique in both phases of polycrystalline austenitic-ferritic stainless steel SAF 2507 formed during low cycle fatigue at two plastic strain amplitudes ap. In individual grains the stress axis and the Schmid factors of active slip systems were determined. In austenitic grains, the planar structures were determined at both ap. In ferritic grains, the dislocation arrangement was different for the two observed ap. Individual screw dislocations and pile-up´s of edge dislocations were found at low ap = 1x10-4. Mixture of vein and wall dislocation structures were formed at high ap = 2x10-3. Observed dislocation structures were discussed in relation with the cyclic plastic response of the duplex stainless steel. | en |
dc.description.mark | A | cs |
dc.identifier.citation | BUČEK, P. Využití techniky orientovaných fólií v TEM [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2009. | cs |
dc.identifier.other | 21885 | cs |
dc.identifier.uri | http://hdl.handle.net/11012/10905 | |
dc.language.iso | cs | cs |
dc.publisher | Vysoké učení technické v Brně. Fakulta strojního inženýrství | cs |
dc.rights | Standardní licenční smlouva - přístup k plnému textu bez omezení | cs |
dc.subject | dislokační struktury | cs |
dc.subject | duplexní korozivzdorná ocel | cs |
dc.subject | TEM | cs |
dc.subject | nízkocyklová únava | cs |
dc.subject | dislocation structures | en |
dc.subject | duplex stainless steel | en |
dc.subject | TEM | en |
dc.subject | low-cycle fatigue | en |
dc.title | Využití techniky orientovaných fólií v TEM | cs |
dc.title.alternative | Application of Technique of Oriented Foils in TEM | en |
dc.type | Text | cs |
dc.type.driver | masterThesis | en |
dc.type.evskp | diplomová práce | cs |
dcterms.dateAccepted | 2009-06-15 | cs |
dcterms.modified | 2009-07-15-11:45:26 | cs |
eprints.affiliatedInstitution.faculty | Fakulta strojního inženýrství | cs |
sync.item.dbid | 21885 | en |
sync.item.dbtype | ZP | en |
sync.item.insts | 2021.11.12 15:25:57 | en |
sync.item.modts | 2021.11.12 14:25:32 | en |
thesis.discipline | Materiálové inženýrství | cs |
thesis.grantor | Vysoké učení technické v Brně. Fakulta strojního inženýrství. Ústav materiálových věd a inženýrství | cs |
thesis.level | Inženýrský | cs |
thesis.name | Ing. | cs |