Show simple item record

dc.contributor.authorAstrouski, Ilyacs
dc.contributor.authorRaudenský, Miroslavcs
dc.contributor.authorKůdelová, Terezacs
dc.contributor.authorKroulíková, Terezacs
dc.date.accessioned2020-12-02T11:55:30Z
dc.date.available2020-12-02T11:55:30Z
dc.date.issued2020-11-02cs
dc.identifier.citationMaterials . 2020, vol. 13, issue 21, p. 1-12.en
dc.identifier.issn1996-1944cs
dc.identifier.other166053cs
dc.identifier.urihttp://hdl.handle.net/11012/195741
dc.description.abstractCurrently, liquid-to-gas heat exchangers in buildings, domestic appliances and the automotive industry are mainly made of copper and aluminum. Using plastic instead of metal can be very beneficial from an economic and environmental point of view. However, it is required that a successful plastic design meets all the requirements of metal heat exchangers. The polymeric hollow fiber heat exchanger studied in this work is completive to common metal finned heat exchangers. Due to its unique design (the use of thousands of thin-walled microtubes connected in parallel), it achieves a high level of compactness and thermal performance, low pressure drops and high operation pressure. This paper focuses on an important aspect of heat exchanger operation-its fouling in conditions relevant to building and domestic application. In heating, ventilation and air conditioning (HVAC) and automotive and domestic appliances, outdoor and domestic dust are the main source of fouling. In this study, a heat exchanger made of polymeric hollow fibers was tested in conditions typical for indoor HVAC equipment, namely with the 20 degrees C room air flowing through the hot water coil (water inlet 50 degrees C) with air velocity of 1.5 m/s. ASHRAE test dust was used as a foulant to model domestic dust. A polymeric heat exchanger with fibers with an outer diameter of 0.6 mm (1960 fibers arranged into 14 layers in total) and a heat transfer area of 0.89 m(2) was tested. It was proven that the smooth polypropylene surface of hollow fibers has a favorable antifouling characteristic. Fouling evolution on the metallic heat transfer surfaces of a similar surface density was about twice as quick as on the plastic one. The experimental results on the plastic heat exchanger showed a 38% decrease in the heat transfer rate and a 91% increase in pressure drops after eighteen days of the experiment when a total of 4000 g/m(2) of the test dust had been injected into the air duct. The decrease in the heat transfer rate of the heat exchanger was influenced mainly by clogging in the frontal area because the first layers were fouled significantly more than the deeper layers.en
dc.formattextcs
dc.format.extent1-12cs
dc.format.mimetypeapplication/pdfcs
dc.language.isoencs
dc.publisherMDPIcs
dc.relation.ispartofMaterialscs
dc.relation.urihttps://www.mdpi.com/1996-1944/13/21/4931cs
dc.rightsCreative Commons Attribution 4.0 Internationalcs
dc.rights.urihttp://creativecommons.org/licenses/by/4.0/cs
dc.subjectpolymeric hollow fiberen
dc.subjectheat exchangersen
dc.subjectheat transferen
dc.subjectfoulingen
dc.titleFouling of Polymeric Hollow Fiber Heat Exchangers by Air Dusten
thesis.grantorVysoké učení technické v Brně. Fakulta strojního inženýrství. Laboratoř přenosu tepla a prouděnícs
sync.item.dbidVAV-166053en
sync.item.dbtypeVAVen
sync.item.insts2021.01.20 20:56:43en
sync.item.modts2021.01.20 20:15:59en
dc.coverage.issue21cs
dc.coverage.volume13cs
dc.identifier.doi10.3390/ma13214931cs
dc.rights.accessopenAccesscs
dc.rights.sherpahttp://www.sherpa.ac.uk/romeo/issn/1996-1944/cs
dc.type.driverarticleen
dc.type.statusPeer-revieweden
dc.type.versionpublishedVersionen


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record

Creative Commons Attribution 4.0 International
Except where otherwise noted, this item's license is described as Creative Commons Attribution 4.0 International