Ústav automatizace inženýrských úloh a informatiky
Browse by
Recent Submissions
-
Seasonal Variability of Resuspension
(EDP Sciences, 2022-11-04)Particulate air pollution in cities is caused by a variety of sources. One of the less-studied contributors is wind-induced particle resuspension. As the wind speed increases, particles are removed from surfaces. These ... -
Reverberation measurement set for the interrupted noise method
(IOP Publishing, 2021-12-21)This paper describes the methodology of measuring the sound absorption coefficient in a reverberation room. For its purpose, a measuring set was created combining professional with widely available hardware suitable for ... -
Case Study of Selected Nature Swimming Pools in the South Moravian Region
(Sciendo, 2021-12-23)Nature swimming pools are a sought-after alternative to conventional swimming pools. Their natural water purification system, without the need for chemicals, is beneficial to health and environmentally friendly. Designing ... -
Classification of the socio-psychological aspects of protecting soft targets: A case study for evacuation of the railway terminals
(University of Žilina, 2021-01-12)Current crisis management approaches to protect soft targets make assumptions about average visitors/listeners/viewers or passengers. They do not give much consideration to impacts of diversity of potentially evacuated ... -
Ductwork pressure loss determination utilizing building information model
(IOP Publishing, 2021-03-15)Building design created as an information model contains not only information formated during building geometry creation but also additional information filled in by a designer. The data can be used further as well as ... -
Machine Learning-Based Node Characterization for Smart Grid Demand Response Flexibility Assessment
(MDPI, 2021-03-09)As energy distribution systems evolve from a traditional hierarchical load structure towards distributed smart grids, flexibility is increasingly investigated as both a key measure and core challenge of grid balancing. ... -
Ventilation design conditions associated with airborne bacteria levels within the wound area during surgical procedures: a systematic review
(W B SAUNDERS CO LTD, 2021-04-27)Without confirmation of the ventilation design conditions (typology and airflow rate), the common practice of identifying unidirectional airflow (UDAF) systems as equivalent to ultra-clean air ventilation systems may be ... -
Neural Network-Based Train Identification in Railway Switches and Crossings Using Accelerometer Data
(Hindawi, 2020-11-24)This paper aims to analyse possibilities of train type identification in railway switches and crossings (S&C) based on accelerometer data by using contemporary machine learning methods such as neural networks. That is a ... -
Moisture diagnostic of a failured roof drainage situated behind a parapet wall and a subsequent condensate influence to a wooden construction
(EDP Sciences, 2016-12-22)There are several possibilities how to deal with a roof drainage. From an architectonic point of view an improper and unsuitable system is chosen in a majority of cases which may be as a logical consequence the beginning ... -
Using BIM model for Fire Emergency Evacuation Plan
(EDP Sciences, 2018-01-22)Is it possible to use building information modelling (BIM) to create a fire emergency evacuation plan in the national condition of the Czech Republic? This article focuses on the advantages and possibilities of using BIM ... -
Train Type Identification at S&C
(Hindawi, 2020-11-24)The presented paper concerns the development of condition monitoring system for railroad switches and crossings that utilizes vibration data. Successful utilization of such system requires a robust and efficient train type ... -
Interface Behavior and Interface Tensile Strength of a Hardened Concrete Mixture with a Coarse Aggregate for Additive Manufacturing
(MDPI, 2020-11-15)3D concrete printing technology (3DCP) is a relatively new technology that was first established in the 1990s. The main weakness of the technology is the interface strength between the extruded layers, which are deposited ... -
Validation of Microscopic Traffic Models Based on GPS Precise Measurement of Vehicle Dynamics
(University of Zagreb, Faculty of Transport and Traffic Sciences, 2013-03-13)In this article we discuss validation of selected microscopic traffic models, based on the comparison of simulated vehicle dynamics with observed dynamic characteristics of vehicles recorded by the precise geodetic GPS equipment. -
Experimental Analysis of Steam Condensation in Vertical Tube with Small Diameter
(Elsevier, 2016-01-12)Thermal design of tubular heat exchanger based on condensation heat of water steam requires knowledge of condensation heat transfer in the each tube. This paper is just aimed on experimental analysis of steam condensation ... -
Portable Telematic System as an Effective Traffic Flow Management in Workzones
(Transport and Telecommunication Institute, 2015-04-18)Traffic infrastructure localities with temporal restrictions for example due to reconstructions, or modernization, are important aspects influencing the traffic safety and traffic flow. On the basis of our research, we can ... -
Bio-Inspired 3D Infill Patterns for Additive Manufacturing and Structural Applications
(MDPI, 2019-02-06)The aim of this paper is to introduce and characterize, both experimentally and numerically, three classes of non-traditional 3D infill patterns at three scales as an alternative to classical 2D infill patterns in the ... -
Application of fire and evacuation models in evaluation of fire safety in railway tunnels
(IOP Publishing, 2017-09-15)The paper describes an application of numerical simulation of fire dynamics and evacuation of people in a tunnel. The software tool Fire Dynamics Simulator is used to simulate temperature resolution and development of smoke ... -
Urban Commuting and Daytime Population In Small Areas of a Metropolis: A Case Study of Brno, Czech Republic
(University of Zagreb, Faculty of Transport and Traffic Sciences, 2009-06-18)A simplified modelling approach to urban commuting patterns is achieved by focusing on daytime populations ratherthan on commuters, or on the commuting process itself.