Fakulta strojního inženýrství
Procházet dle
Kolekce v této sbírce
-
Energetický ústav [26]
-
Letecký ústav [4]
-
NETME Centre [1]
-
Sekce matematiky [3]
-
Ústav jazyků [1]
-
Ústav konstruování [13]
-
Ústav matematiky [10]
Poslední příspěvky
-
Comparison of the Resistance to Bending Forces of the 4.5 LCP Plate-rod Construct and of 4.5 LCP Alone Applied to Segmental Femoral Defects in Miniature Pigs
(University of Veterinary and Pharmaceutical Sciences in Brno, 2010-12-20)The study deals with the determination of mechanical properties, namely resistance to bending forces, of flexible buttress osteosynthesis using two different bone-implant constructs stabilizing experimental segmental femoral ... -
Implementation of American weld connection standards into finite element computations
(IOP Publishing, 2017-03-01)Presented paper summarizes the weld assessment on the basis of national standards. The approach concerning the static loading has been still not adequately developed in standards. The standard of American Institute of Steel ... -
Spatio-temporal description of the cavitating flow behavior around NACA 2412 hydrofoil
(IOP Publishing, 2015-12-06)Spatio-temporal description of the cavitating flow around hydrofoil with 8 degrees incidence using proper orthogonal decomposition (POD) is presented. POD is a suitable tool, which provides information not only about the ... -
A Practical Approach for the Calculation of the Activation Energy of the Sintering
(International Institute for the Science of Sintering, 2016-12-15)Newly developed software for calculation of activation energy (Qs in the following) of sintering using the Wang and Raj model is presented. To demonstrate the practical potential of the software and to evaluate the behaviour ... -
An accuracy analysis of the front tracking method and interface capturing methods for the solution of heat transfer problems with phase changes
(IOP Publishing, 2016-06-19)Materials undergoing a phase change have a number of applications in practice and engineering. Computer simulation tools are often used for investigation of such heat transfer problems with phase changes since they are ... -
Valve exploiting the principle of a side channel turbine
(IOP Publishing, 2017-04-04)The presented article deals with a side channel turbine, which can be used as a suitable substitute for a pressure reducing valve. Pressure reducing valves are a source of high hydraulic losses. The aim is to replace them ... -
Experimental study of in-line heat treatment of 1.0577 structural steel
(Elsevier, 2018-09-16)In-line heat treatment is frequently used in rolling mills because it offers a significant improvement of rolled product mechanical properties with costs benefits. This method allows achieving required mechanical properties ... -
Dynamic Loading of Lattice Structure Made by Selective Laser Melting-Numerical Model with Substitution of Geometrical Imperfections
(MDPI, 2018-10-29)This article deals with the prediction of lattice structure mechanical properties under dynamic loading using finite element method (FEA) with inclusion of geometrical imperfections of the SLM process. Such properties are ... -
Higher in-flight particle velocities enhance in vitro tribological behavior of plasma sprayed hydroxyapatite coatings
(Elsevier, 2016-11-01)Hydroxyapatite (HA) coatings were deposited onto Ti6Al4V substrates via atmospheric plasma spraying under systematically varying spray parameters, leading to different in-flight particle velocities. Morphology, composition, ... -
Evaluation of the technical condition of medium-sized boilers
(EDP Sciences, 2018-03-14)The recent trend in the steam and electricity production has been both to increase the efficiency of the facility and to keep tightening legislation concerning emission limits. The lifetime of energy equipment is greatly ... -
Risk Management and Knowledge Management as Critical Success Factors of Sustainability Projects
(MDPI, 2018-05-05)The paper is focused on the analysis of the key aspects of sustainability projects, namely advanced risk management and project knowledge. These aspects are recommended to the attention of institutions and project managers ... -
New boundary conditions for fluid interaction with hydrophobic surface
(EDP Sciences, 2018-06-04)Solution of both laminar and turbulent flow with consideration of hydrophobic surface is based on the original Navier assumption that the shear stress on the hydrophobic surface is directly proportional to the slipping ... -
Comparison of two inlet boundary approaches in numerical simulation of car ventilation outlet flow
(EDP Sciences, 2015-11-17)The paper is concerned with the comparison of two inlet boundary approaches of numerical simulations. The first approach is based on the simulation of a sufficiently long duct upstream the area of interest with known ... -
Quantitative phase imaging unravels new insight into dynamics of mesenchymal and amoeboid cancer cell invasion
(Springer Nature, 2018-08-13)Observation and analysis of cancer cell behaviour in 3D environment is essential for full understanding of the mechanisms of cancer cell invasion. However, label-free imaging of live cells in 3D conditions is optically ... -
Frictional response of lubricant in EHL contact under transient bi-directional shear loading
(Serbian Tribology Society, 2017-12-15)Consideration of performance, efficiency and energy consumption is nowadays an inherent part of the design of every modern machine. These factors are mainly determined by mechanisms taking place within the lubricated ... -
Heavy-Duty Transmission Gear Shift Investigation by Virtual Prototypes
(JVE Intenational, 2018-05-22)This paper deals with application of virtual prototype to the heavy-duty vehicles gearbox concept. Used methodology was developed and validated on the single stage gearbox concept. Afterwards the virtual prototype was ... -
Experimental and Computational Evaluation of Rolling Bearing Steel Durability
(Tanger Ltd., 2016-11-09)Rolling element bearings are widely-used machine components and their failure can result in damage to the whole machine. A bearing failure can be caused by many factors. In most cases it is damage on the raceway surface ... -
Selective Laser Melting Strategy for Fabrication of Thin Struts Usable in Lattice Structures
(MDPI, 2018-09-18)This paper deals with the selective laser melting (SLM) processing strategy for strut-lattice structure production which uses only contour lines and allows the porosity and roughness level to be managed based on ombination ... -
Joint Rock Coefficient Estimation Based on Hausdorff Dimension
(Scientific Research Publishing, 2017-12-18)The strength of rock structures strongly depends inter alia on surface irregularities of rock joints. These irregularities are characterized by a coefficient of joint roughness. For its estimation, visual comparison is ... -
Bulk viscosity of water in acoustic modal analysis and experiment
(EDP Sciences, 2018-06-04)Bulk viscosity is an important factor in the damping properties of fluid systems and exhibits frequency dependent behaviour. A comparison between modal analysis in ANSYS Acoustics, custom code and experimental data is ...
RSS 1.0