Prohlížení Ústav materiálových věd a inženýrství dle názvu
Zobrazují se záznamy 1-16 z 16
-
Effect of heat treatment on mechanical properties and residual stresses in additively manufactured parts
(Institute of Theoretical and Applied Mechanics of the Czech Academy of Sciences, 2018-05-14)Heat treatments commonly used for post-processing in additive manufacturing (AM) deal with relieving residual stresses. However, generally these treatments reduce strength properties of material such as yield stress (YS) ... -
Elastic and Plastic Behavior of the QE22 Magnesium Alloy Reinforced with Short Saffil Fibers and SiC Particles
(MDPI AG, 2018-02-15)Magnesium alloy QE22 (nominal composition 2 wt % Ag, 2 wt % mixture of rare earth elements, balance Mg) was reinforced with 5 vol % Saffil fibers and 15 vol % SiC particles. The hybrid composite was prepared via the squeeze ... -
In-Flight Temperature And Velocity of Powder Particles of Plasma Sprayed TiO2
(Springer, 2013-10-25)This paper relates to the in-flight temperature and velocity of TiO2 particles, an integral part of the systematic research on atmospheric plasma spraying of the material. Initial powder feedstock (32-45 um, 100% rutile ... -
Influence of Cold-Sprayed, Warm-Sprayed and Plasma Sprayed Layers Deposition on Fatigue Properties of Steel Specimens
(Springer, 2015-03-10)Titanium powder was deposited onto steel specimens using four thermal spray technologies: plasma spray, low-pressure cold spray, portable cold spray, and warm spray. The specimens were then subjected to strain controlled ... -
Influence of plasma and cold spray deposited Ti Layers on high-cycle fatigue properties of Ti6Al4V substrates
(Elsevier, 2013-02-25)This paper presents a summary of the research on the influence of plasma and cold spray deposition of bio-grade Ti powder on the high-cycle fatigue properties of Ti6Al4V substrates. Four sets of flat specimens (as-received, ... -
Influence of plasma electrolytic oxidation on fatigue performance of AZ61 magnesium alloy
(Elsevier, 2014-05-01)The effect of plasma electrolytic oxidation (PEO) on the fatigue of AZ61 magnesium alloy has been investigated under high cycle conditions in air and 3.5% NaCl solution. PEOemployed an alkaline pyrophosphate-silicate-fluoride ... -
Influence of Processing Techniques on Microstructure and Mechanical Properties of a Biodegradable Mg-3Zn-2Ca Alloy
(MDPI, 2016-10-28)New Mg-3Zn-2Ca magnesium alloy was prepared using different processing techniques: gravity casting as well as squeeze casting in liquid and semisolid states. Materials were further thermally treated; thermal treatment of ... -
Influence of Scanning Strategies on Processing of Aluminum Alloy EN AW 2618 Using Selective Laser Melting
(MDPI, 2018-02-14)This paper deals with various selective laser melting (SLM) processing strategies for aluminum 2618 powder in order to get material densities and properties close to conventionally-produced, high-strength 2618 alloy. To ... -
Master Sintering Curve - A Practical Approach to its Construction
(International Institute for the Science of Sintering, 2010-04-01)A practical method for the construction of MSC is presented in the paper. With the help of a few dilatometric sintering experiments the newly developed software calculates MSC and finds the optimal activation energy of a ... -
Master Sintering Surface – A Practical Approach to Its Construction and Utilization for Spark Plasma Sintering Prediction
(International Institute for the Science of Sintering, 2012-08-01)The sintering is a complex thermally activated process, thus any prediction of sintering behaviour is very welcome not only for industrial purposes. Presented paper shows the possibility of densification prediction based ... -
Modification of Plasma Sprayed TiO2 Coatings Characteristics via Controlling the In-flight Temperature and Velocity of the Powder Particles
(Springer, 2014-08-27)The study presents a comprehensive research on the plasma spray fabrication of TiO2 coatings with microstructural properties adjustable via controlling the respective in-flight properties of the feedstock particles. The ... -
Oxidation Performance of Cold Spray Ti-Al Barrier Coated gamma-TiAl Intermetallic Substrates
(Elsevier, 2015-04-04)Four blends of Al powder containing different amounts of Ti were deposited onto Ti-46Al-7Nb substrates as oxidation-protection layers using low-pressure cold spray. The coating morphology and chemical composition were ... -
A Practical Approach for the Calculation of the Activation Energy of the Sintering
(International Institute for the Science of Sintering, 2016-12-15)Newly developed software for calculation of activation energy (Qs in the following) of sintering using the Wang and Raj model is presented. To demonstrate the practical potential of the software and to evaluate the behaviour ... -
Role of In-flight Temperature and Velocity of Powder Particles on Plasma Sprayed Hydroxyapatite Coating Characteristics
(Elsevier, 2012-01-15)This paper presents a systematic research on the process of thermal spraying of HA encompassing all stages of layer deposition: powder production and characterization (optimized production led to spherical 29.29 - 50.51 ... -
Selective Laser Melting Strategy for Fabrication of Thin Struts Usable in Lattice Structures
(MDPI, 2018-09-18)This paper deals with the selective laser melting (SLM) processing strategy for strut-lattice structure production which uses only contour lines and allows the porosity and roughness level to be managed based on ombination ... -
Sintering Densification Curve - a Practical Approach For Its Construction From Dilatometric Shrinkage Data
(International Institute for the Science of Sintering, 2008-01-01)This article summarizes the usage of high-temperature dilatometry in ceramic processing and powder technology with special attention on the description of the sintering process. A practical method for transformation of ...