• 1200 W flyback switching power supply with silicon carbide semiconductors 

    Martiš, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper shows how a recent advancement in power semiconductor technology and some improvements can allow the flyback switching power supply to operate effectively at high output powers. The switching frequency can be ...
  • 3D Dental Scanner 

    Kotek, L. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper is about 3D scan of plaster dental casts. The main aim of the work is a hardware and software proposition of 3D scan system for scanning of dental casts. There were used camera, projector and rotate table for ...
  • Acceleration Unit for HTTP Headers Identification in FPGA 

    Bryndza, Ivan (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper presents a hardware accelerated identification of HTTP protocol headers, since HTTP is the most used protocol on the Internet. We have designed a hardware architecture, which will be used for detection of HTTP ...
  • Acoustical detection of gunshots in the open 

    Hrabina, M., (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper descibes development of reliable gunshot detection system without need of localization, with emphasis on low power consumption for use in counter-poacher devices primarily protecting elephants in Africa. Intended ...
  • Aeroplane model control using ISM 433 band 

    Juráň, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The aim of this work was to design multifunctional pair of devices for wireless transmission. Next goal was to use it to create RC model from hand launch glider to demonstrate wide possibilities of the developed system.
  • Analysis and Prediction of Reliability of Solder Joints 

    Novotný, V. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This article deals with the sphere of solder joints reliability and narrower focus is using simulation software ANSYS and fatigue models for estimate reliabity of solder joints. The text describes the introduction to the ...
  • Analysis of Defects on PCB Using X - Plane Method 

    Mlýnek, M. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    Using x – ray is one way for analyzing structural defects on PCB and lead components. X – Plane method is based on making individual 2D slices within a sample from top to bottom, front to back and left to right. There is ...
  • Analysis of High Speed Squirrel Cage Induction Motor With Influence of Riveting 

    Klíma, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper deals with analyzing of high speed squirrel cage induction motor and the influence of riveting stator stack. The model of high speed induction motor was made in ANSYS Maxwell software in accordance with provided ...
  • Analyzing of photovoltaic power plant Dukovany 

    Mačát, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The article is about researching of the oldest photovoltaic panels in the Czech Republic. There are mentioned several methods of investigation using after 17 years working of photovoltaic power station. Then the article ...
  • Ant Run Game for 8x8 LED Matrix 

    Jankech, T. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The aim of this project is an implementation of the Ant Run game to the FRDM-KL25Z development board with 8x8 RG LED matrix shield. The game is principally controlled by a builtin accelerometer on the FRDM-KL25Z. The work ...
  • Assessment of noise sources in resistors 

    Kuparowitz, T. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    Thermal noise and 1/f noise are investigated at room conditions in three kinds of basic off-the-shelf resistors. Samples of carbon film, metal oxide, and cement fixed wire-wound resistors are evaluated. Measurement setup ...
  • Audio Mixer Used for Laboratory Measurements 

    Kalina, L. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This project describes the microphone preamplifier which is part of the second channel audio mixing console. In this circuit are used low noise and low THD amplifiers. As an integral part of this project is a design of ...
  • Authentication Using Mobile Phones 

    Fusek, Z. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This project deals with authentication by a mobile device. The mobile device with the operating system Android 5.0 was chosen as authentication device. The user can perform authentication with emulation of contactless chip ...
  • Authentication via Smartphone with NFC 

    Horák, M. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This work is about replacement smartphones instead of smart cards in acces control. The main goal is to create an application which runs on Android and has the same function as a smart card. The requirements for this task ...
  • Automated Shooting Range for Air Pistols 

    Radvanský, M. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This work deals with the design and manufacture of the device, which is used as a shooting range to practice shooting with an air gun. The device is controlled by the Arduino MEGA and could be connect to any number of smart ...
  • Automatic Delineation of QRS Complex 

    Zimolka, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This article details my realization of the QRS delineation, based on the method introduced by Laguna, Jané and Caminal, described in the first part. The folowing part describes my realization and modifications aimed at the ...
  • Automatic Water System of Greenhouse 

    Prokop, M. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The objective of this thesis is a design of automatic water system of greenhouse, which will be able measure temperature, relative humidity of air and soil. System will control air and water management based on these values.
  • Autonomous Car Path Optimalization 

    Vladyka, V. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    This paper deals with path search and optimalisation of model car in unknown space. All data from sensors are processed in real-time onboard at ARM Cortex M4 microcontroller. Model’s main sensor is line-scan camera.
  • Backscatter modulator for UHF RFID tag emulator 

    Janošík, T. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The paper describes design of external backscatter modulator for RFID tag emulator, which is used in UHF band. This modulator is connected with the Universal Software Radio Peripheral and antenna. Realization of a backscatter ...
  • Basic Measurement of Dynamic Properties of Amplifier with Bipolar Transistor 

    Repčík, J. (Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, 2015)
    The aim of this article is to analyze the theoretical basis of amplifier with bipolar transistors measurement. In particular, this contribution focuses on a convenient way of setting the operating point of an amplifier ...