Multifunkční pavilon
Loading...
Date
Authors
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta stavební
Abstract
Předmětem diplomové práce je návrh a posouzení nosné konstrukce pavilonu, pro výstavní a jiné účely. Samotná stavba se nachází v blízkosti města Zlína. Byly vytvořeny předběžné návrhy nosné konstrukce, z nichž jeden byl vybrán, podrobně navrhnut a posouzen. Celkově se jedná o dvě konstrukce, které jsou mezi sebou dilatovány. Byl vytvořen návrh a posouzení vstupního portálu pro výstavní pavilon. Vstupní portál je atypická konstrukce. Jedná se o příhradovou skořepinu ve tvaru hyperboloidu a válce. Vstupní portál má proměnnou výšku, kde největší výška činní 8,258m. Portál je dlouhý 20,394m a má proměnnou šířku, z nichž největší je 12,000m. Samotná výstavní hala, která je umístěna za vstupní portál, byla navržena z rovinných obloukových příhradových vazníků. Obloukové vazníky jsou vytvořeny z několika poloměrů a celkově budí dojem eliptického tvaru vazníku. Vazníky mají rozpětí 37,000m a jsou od sebe osově vzdáleny 6,000m. Výška obloukových vazníků činní 10,530m. V čele konstrukce byly navrženy sloupy a konstrukce pro možné připojení vstupního portálu, popřípadě pro umístění vratového systému. Celá konstrukce výstavního pavilonu, bez vstupního portálu, je dlouhá 54,000m a široká 37,000m. Zastavěná plocha obou konstrukcí činní přibližně 2200m2. Konstrukce jsou navrženy dle normativních požadavků ČSN EN na mezní stav únosnosti a použitelnosti. Jako hlavní materiál nosných prvků konstrukce, byla použita ocel S355JR.
The subject of the diploma thesi is the design and assessment of the pavilions supporting structure for exhibition and other purposes. The building is located close to Zlin. Preliminary designs of supporting structure were created. One of these was selected and detaileddesigned and assessed. Generallythere are two structures that are extended between themselves. A design and assessment of the entrance portal for the exhibition pavilion was created. The entrance portal is an atypical structure that was created from a combination of hyperboloid and cylinder. The entire portal is formed of welded parts and it is completely from glass. The entrance portal has a variable height, where the highest point is 8,258m. The entrance portal is 20,394m long and has a variable width, where the largest width is 12,000m. The exhibition hall, which is located behind the entrance portal was designed from flat arched truss trusses. The arched trusses are made of several radii and hasa overall impression of an elliptical truss. The trusses have a range 37,000m and they are axially distant 6,000m. The height of the arched trusses is 10.530m. In the leading position of the construction were designed pillars and construction for possible connection of the entrance portal, or for the location of the gate system. Whole construction of the exhibition pavilion, without the entry portal, is 54,000m long and 37,000m wide. The built-up area of both structures is approximately 2200m2. Construction are designed according to normative requirements of CSN EN for limit state of load capacity and usability. The main material of the supporting structural parts was used S355JR steel.
The subject of the diploma thesi is the design and assessment of the pavilions supporting structure for exhibition and other purposes. The building is located close to Zlin. Preliminary designs of supporting structure were created. One of these was selected and detaileddesigned and assessed. Generallythere are two structures that are extended between themselves. A design and assessment of the entrance portal for the exhibition pavilion was created. The entrance portal is an atypical structure that was created from a combination of hyperboloid and cylinder. The entire portal is formed of welded parts and it is completely from glass. The entrance portal has a variable height, where the highest point is 8,258m. The entrance portal is 20,394m long and has a variable width, where the largest width is 12,000m. The exhibition hall, which is located behind the entrance portal was designed from flat arched truss trusses. The arched trusses are made of several radii and hasa overall impression of an elliptical truss. The trusses have a range 37,000m and they are axially distant 6,000m. The height of the arched trusses is 10.530m. In the leading position of the construction were designed pillars and construction for possible connection of the entrance portal, or for the location of the gate system. Whole construction of the exhibition pavilion, without the entry portal, is 54,000m long and 37,000m wide. The built-up area of both structures is approximately 2200m2. Construction are designed according to normative requirements of CSN EN for limit state of load capacity and usability. The main material of the supporting structural parts was used S355JR steel.
Description
Citation
DVOULETÝ, M. Multifunkční pavilon [online]. Brno: Vysoké učení technické v Brně. Fakulta stavební. 2018.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Konstrukce a dopravní stavby
Comittee
Date of acceptance
2018-01-31
Defence
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení